Product Range
Accessories

Hydraulic accessories


Coupling devices
Coupling devices are essential accessories for making a reversible hydraulic connection between the pump and the outlet piping. This system allows the pump to be brought to the surface and then quickly reconnected, with no need to drain the tank, often an expensive operation involving lengthy plant ...
  • DAC E (GAS 2")
    DAC E (GAS 2")
    DAC E (GAS 2")
    Hydraulic accessories
  • DAC H (DN32 PN6 - DN50 PN10)
    DAC H (DN32 PN6 - DN50 PN10)
    DAC H (DN32 PN6 - DN50 PN10)
    • structure in GJL-250 cast iron
    • seal in NBR rubber
    • epoxy-vinyl paint
    • full free passage
    • complete with pipe guide, sliding flange (including stainless steel fasteners) and 2" GAS threaded bend in stainless steel
  • DAC H (DN65-DN250)
    DAC H (DN65-DN250)
    DAC H (DN65-DN250)
    • structure in GJL-250 cast iron
    • seal in NBR rubber
    • epoxy-vinyl paint
    • full free passage
    • complete with pipe guide and sliding flange with stainless steel fasteners
    • a patented system simplifies pump release and reduces the mechanical stresses on the guide pipes
  • DAC V (1 1/2” - 2” ; DN32 PN6 - DN50 PN10)
    DAC V (1 1/2” - 2” ; DN32 PN6 - DN50 PN10)
    DAC V (1 1/2” - 2” ; DN32 PN6 - DN50 PN10)
    Hydraulic accessories
  • DAC V (DN65-DN300)
    DAC V (DN65-DN300)
    DAC V (DN65-DN300)
    Hydraulic accessories
  • DAC X
    DAC X
    DAC X
    • structure and flange in AISI 316 stainless steel
    • seal in NBR
    • full free passage
    • recommended for installations with corrosive or saline liquids
 
Accessories for coupling devices
A wide range of accessories for coupling devices allow any type of plant to be optimized and reduce installation times.
  • KAF
    KAF
    KAF
    Sliding flange for:
    • OXY50 (KAF 32-50)
    • DAC H (check the dimensions of KAF for correct coupling)
    • DAC V (check the dimensions of KAF for correct coupling)
    This accessory can be coupled to Flygt devices.
  • KGP
    KGP
    KGP
    Hydraulic accessories
 
Base plate
Base plates for FREE installation allow the pump to be positioned in the tank quickly and ensure a high level of stability thanks to
the large contact surface. Made of cast iron (GJS-600.3) or galvanized steel. Complete with stainless steel scew.
  • 9024.006
    9024.006
    9024.006
    Hydraulic accessories
  • 9024.007
    9024.007
    9024.007
    Hydraulic accessories
  • 9024.008
    9024.008
    9024.008
    Hot-galvanised steel base plate.
    Suitable for the following models:
    • GRN 300-400/4/80-100
  • 9024.009
    9024.009
    9024.009
    Hydraulic accessories
  • 9024.010
    9024.010
    9024.010
    Cast iron 3 spoke base plate for free installation.
    Suitable for the following models:
    • DGF 150-200/2/G65V-65-80
    • DGO 150-200/2/G65V-65-80
 
Check valves
Zenit check valves, certified EN 12050-4 annex ZA standard EN 12050-4, are designed for use even with soiled liquids and provide full guarantees of operation even under heavy-duty working conditions.
The sinking ball system ensures a free passage since, at maximum opening, the valve has a completel...
  • VAC
    VAC
    VAC
    Hydraulic accessories
  • VAP
    VAP
    VAP
    Hydraulic accessories
 
Gate valves
The knife gate valves, with handwheel control, have various functions and are used as interception units to regulate the flow in a pipeline or to temporarily isolate a section of the plant.
The gate valves have a structure in GJL-250 cast iron inside of which are the mechanisms used to partially or...
  • SRP
    SRP
    SRP
    • structure in GJL-250 cast iron
    • stainless steel shaft with O-ring seal
    • bronze seats
    • epoxy paint
    • can be installed in a horizontal or vertical position
    • integral free passage when fully open
 
Bend unions
Zenit bend unions are made from GFL-250 cast iron or galvanized steel and have UNI standard flanges to guarantee complete interchangeability.
There are 2 types of bend unions: inlet and outlet.
Inlet bend unions + the hydraulic connection to be made to pumps for dry chamber installations.
This ac...
  • KBC
    KBC
    KBC
    • structure made of GJL-250 cast iron or galvanized steel
    • epoxy paint
    • seal in NBR
  • KCR
    KCR
    KCR
    MALE-FEMALE THREAD (GAS 2”)
    • structure in stainless steel
    FLANGE-THREAD (DN80-DN100)
    • structure in GJL-250 cast iron
    • epoxy paint
    • seal in NBR
    FLANGE-FLANGE (DN65 PN10-16÷DN250 PN10)
    • structure made of GJL-250 cast iron or galvanized steel
    • epoxy paint
    • seal in NBR
 
Flange
Flange in GJL-250 cast iron
  • KFL
    KFL
    KFL
    Flange in GJL-250 cast iron painted with epoxy coating.
    Cast iron flange to transform the delivery port from GAS 11/2” to GAS 2”.
    Designed to be coupled to electric pumps with DN32 PN6 outlet flange.
    Threaded and welded flanges PN6 and PN 10-16 in accordance with standard EN 1092-1
 
Flushing valve
Sediments often form in lifting stations which collect the wastewater from drain systems.
Over time, the solids tend to compact on the bottom and sides of the tank, reducing its volume, and when they break away they very often foul the pump.
A specific operation, involving a lengthy, expensive sys...
  • FLX
    FLX
    FLX
    Hydraulic accessories